Solar-Ready Commercial Roofs in San Antonio and Austin

Roofing Contractors Association of Texas member BBB Accredited Business with an A+ rating

Solar-Ready Commercial Roofs in San Antonio and Austin

A solar array is meant to stay on a commercial roof for a long time. If the roof under it wears out first, the panels have to come off before the roof can be replaced. A solar-ready roof system gets the roof right before the array goes on: a sound structure, a new or renewed weather surface, and drainage, flashings and access planned around the layout.

At Total Cladding and Roofing, we prepare commercial roofs in San Antonio and Austin for solar. On a low-slope roof that usually means a TPO roof replacement or recover; on a worn metal building, a metal roof retrofit with an insulation upgrade. Your solar contractor designs and installs the array, and we coordinate the roof work with them.

Safety on site

Supporting Your Project

Related Services for Commercial Roofs

Commercial Roof Surveys in San Antonio and Austin

Explore this topic

Preventive Roof Maintenance and Asset Management in Texas

Explore this topic

Commercial Roof Coating Contractors in San Antonio and Austin

Explore this topic

Metal Roof Restoration Contractors in San Antonio and Austin

Explore this topic

Commercial Metal Roof Retrofit in San Antonio and Austin

Explore this topic

Commercial R-Panel Roofing and Wall Cladding in San Antonio and Austin

Explore this topic

Benefits of Solar-Ready Roof Systems

Future roof access

Solar equipment changes access to the roof. Drainage routes, skylights and maintenance areas need space in the proposed layout.

Insulation Before the Array

Adding insulation is far simpler during a roof replacement or retrofit than after panels cover the roof.

Structural Check

The array adds weight and wind load, so we bring in a structural review of the deck, purlins and frames where the layout calls for it.

Planned Penetrations

Mounts, conduit and curbs are flashed into a new roof instead of being cut into a worn one.

Solar-Ready Roofing Services We Provide

Our solar-ready roofing work includes:

TPO Roof Replacement and Recover

A new heat-welded TPO membrane on a low-slope roof. Read about TPO roofing in San Antonio or in Austin.

Metal Roof Retrofit

A new metal roof on sub-purlins over a worn metal building roof, described on our San Antonio retrofit and Austin retrofit pages.

Insulation & R-Value Upgrades

Added above the deck or within the retrofit cavity while the whole roof is still open.

Flashings for Mounts and Conduit

Curbs, pipe flashings and conduit penetrations detailed into the new roof.

Replacement planning

We select the roofing and details for the building, then explain the care and inspection needs of the new roof.

Coordination With Your Solar Installer

Layout, mount types, walkways and work sequence agreed with the solar contractor you choose.

A documented sequence

Our Solar-Ready Roof Process

  1. Roof Assessment – Evaluating the roof’s condition, moisture and structure against the planned array.

  2. System Design – Recommending a TPO roof, a metal roof retrofit or a coating, with the insulation and details to suit the array.

  3. Preparation & Installation – Installing the new roof or coating before the array goes on.

  4. Coordination During Solar Work – Working with your solar contractor on mounts, penetrations and protection of the new roof.

  5. Final Verification – Checking the roof and its details once the array is in place.

Why Choose Us for a Solar-Ready Roof

Commercial & Industrial Only

Warehouses, plants, retail buildings and offices.

Veteran Roofing Judgment

More than 20 years of commercial roofing, and a direct answer on whether the roof should be replaced, retrofitted or coated before solar.

Central Texas Weather

Drainage planned for heavy rain running between array rows, and membranes chosen for hail and UV.

Occupied Buildings

Access, work areas, phasing and protection agreed with your site team.

Refurbishment focus

We retrofit, recover and coat existing roofs, with the work based on the condition of your building.

Industries We Serve

We provide solar-ready roofing for:

  • Warehouses & Distribution Centers

  • Manufacturing Plants

  • Retail & Shopping Centers

  • Office Buildings & Complexes

  • Schools & Universities

  • Hospitals & Healthcare Facilities

  • Government & Public Facilities

Where We Prepare Roofs for Solar

Our solar-ready roof systems are available for commercial buildings in:

  • San Antonio, east along I-10 to Seguin

  • Austin, including the SH 130 corridor through Pflugerville

Talk to our team

Contact Us Today

Get the roof right before the array goes on with a solar-ready roof system from Total Cladding and Roofing. We work from Bulverde, about half an hour’s drive from central San Antonio; central Austin is around an hour and 20 minutes away.

Call (210) 775-0995 or send us your roof details, and tell us when the solar work is planned.

Discuss Your Project

Frequently asked questions

Solar-ready Commercial Roof Planning FAQs

What does solar-ready roofing mean?

Preparing the roof condition, layout and connections for a proposed solar installation. It does not by itself confirm structural capacity or electrical design.

Should an aging roof be replaced before solar is installed?

Usually. If a survey shows the roof is worn, replace, recover or retrofit it first. Taking solar equipment off later to rework the roof adds cost and disruption.

Can every roof support solar panels?

No. The proposed loads and attachments need assessment for the actual structure and roof system by the responsible designer.

Can panels be attached to standing seams without penetrations?

Some systems use compatible clamps, but seam type, loading and roof movement must be checked. Visual fit alone is not enough.

Do solar layouts affect drainage?

They can obstruct access or interact with roof details. Drains, maintenance routes and equipment clearances need to remain usable.

Who handles the electrical work?

Electrical design and installation belong with the appropriately qualified solar or electrical contractor. Roofing work is coordinated with that team.

Which roof suits solar on a commercial building in San Antonio or Austin?

On a true low-slope roof, a TPO roof system with new insulation and flashings is the usual choice. On a pre-engineered metal building, a metal roof retrofit gives a new roof on sub-purlins, with room for added insulation, ahead of the solar work.

Can existing roof leaks be left until after solar work?

Unresolved leaks need investigation before equipment limits access. Identify and price the roofing work alongside the solar project.

What affects the roofing preparation cost?

Existing condition, roof openings and attachment details all count, along with whether the roof needs a recover, a retrofit, a coating, more insulation or full replacement.

What should be supplied for a review?

The address, roof records and proposed solar layout or designer contact. Share any known leaks and the intended installation timing.

UK refurbishment experience, a Texas office

Refurbishment specialists

Our business grew through roof and cladding refurbishment in the UK. That experience shapes the work we now offer from our Texas office.

Repair what can be retained

We investigate the roof problem and explain what can be repaired, restored or replaced, so you can decide how to invest in the building.

Roofing and cladding together

We can coordinate roof, insulation, wall panel and drainage work, including the connections where separate repairs can leave problems behind.

A plan for your working building

We agree access, work areas and protection with your site team, including any restrictions needed while the roof is opened.

Roofing and cladding systems

Roofing systems and materials for Texas facilities

Rustoleum Logo
Sika Logo
Kingspan Logo
Morin Logo
American WeatherStar Logo
GAF Logo
TAMKO Logo
PAC-CLAD Logo
1

Tell us about the building

Start with the address and the roof or cladding problem. Photographs are helpful if you already have them.

2

Arrange a site visit

We review the affected areas and discuss how you use the building and what you want the work to achieve.

3

Review the quotation

Your quotation explains the proposed repairs or refurbishment, the areas included and the price.

4

Agree the work plan

We discuss timing, access, deliveries and protection with your site contact before work begins.

5

Complete the work

We carry out the agreed work and discuss any changes needed if opening the roof reveals additional damage.

6

Handover

We review the completed work and provide the care information and documents included in your project.